可按以下的步骤手工同步二块 supervisor engines: 命令 Step 1 Router(config)# redundancy 目的
进入冗余配置模式 Step 2 Router(config-r)# main-cpu 进入 main-cpu 配置模式 Step 3
Router(config-r-mc)# auto-sync {startup-config | config-register | bootvar |
standard} 同步配置参数，有 startup-config, config-register,bootvar,standard Step 4
Router(config-r-mc)# end 退回全局模式 sobey 数码科技股份有限公司 网络系统项目部 6000 交换机简要配置手册 Step 5
Router# copy running-config startup-config 保存配置 注 意 auto-sync standard 命 令 不 同 步
boot variables. 配置如下： Router(config)# redundancy Router(config-r)# main-cpu
Router(config-r-mc)# auto-sync standard Router(config-r-mc)# auto-sync bootvar
Router(config-r-mc)# end Router# copy running-config startup-config 注意
手工同步某参数后，会使原缺省的同步 特征 3.2. 查看 Supervisor Engine 冗余 Command Router# show module
all Purpose Display the redundancy configuration. 如下 Router# show module all Mod
Ports Card Type 1 2 3 4 5 2 2 48 48 16 Catalyst 6000 supervisor 2 (Standby)
Catalyst 6000 supervisor 2 (Active) Model WS-X6K-SUP2-2GE WS-X6K-SUP2-2GE
WS-X6548-RJ-45 WS-X6548-RJ-45 Serial No. SAD04450LEU SAD04160FSR SAD050105Y0
SAD0440799G SAD05030P0W 网络系统项目部 --- ----- --------------------------------------
------------------ ----------- SFM-capable 48-port 10/100 Mbps RJ45 SFM-capable
48-port 10/100 Mbps RJ45 SFM-capable 16 port 10/100/1000mb RJ45 WS-X6516-GE-TX
sobey 数码科技股份有限公司 6000 交换机简要配置手册 7 8 9 11 12 13 0 0 16 16 16 16 Switching Fabric
Module-136 (Active) Switching Fabric Module-136 (Standby) Pure SFM-mode 16 port
1000mb GBIC Pure SFM-mode 16 port 1000mb GBIC Pure SFM-mode 16 port 1000mb GBIC
Pure SFM-mode 16 port 1000mb GBIC Hw 1.1 WS-X6500-SFM2 WS-X6500-SFM2
WS-X6816-GBIC WS-X6816-GBIC WS-X6816-GBIC WS-X6816-GBIC Fw Unknown Sw 6.2(0.106)
6.2(0.106) 6.2(0.106) 6.2(0.106) 6.2(0.106) 6.2(0.106) 6.2(0.106) Ok Ok Ok Ok Ok
Ok Ok SAD04440663 SAD04510at4 SAD044904N7 SAD04390CCJ SAD04260E24 SAD04260E1J
Status Mod MAC addresses 1 2 3 4 5 7 8 9 11 12 13 0001.6461.38a8 to
0001.6461.38a9 0040.0b14.03e2 to 0040.0b14.03e3 0001.6441.47f0 to 0001.6441.481f
0002.b9ff.e8d0 to 0002.b9ff.e8ff 0001.64f8.3330 to 0001.64f8.333f 0040.0bff.0000
to 0040.0bff.0000 0040.0bff.0000 to 0040.0bff.0000 0002.fc90.0888 to
0002.fc90.0897 0001.64f8.37f0 to 0001.64f8.37ff 0001.64f8.3180 to 0001.64f8.318f
0001.64f8.3190 to 0001.64f8.319f --- ---------------------------------- ------
------------ ------------ ------0.220 6.1(2) 0.303 6.1(3) 0.204 6.1(3) 0.201
6.1(2) 0.107 6.1(3) 0.203 6.1(3) 0.302 12.1(4r) 0.204 12.1(5r) 0.105 12.1(5r)
0.105 12.1(5r) Serial SAD044509Y3 SAD04130A17 SAD04160DBN SAD04460KEJ
SAD04460KEL SAD04440952 SAD04390CCJ SAD04340BK2 SAD04340BK0 12.1(nightly Ok
12.1(nightly Ok 12.1(nightly Ok 12.1(nightly Ok Hw 1.1 0.305 0.205 0.205 0.215
0.215 0.118 0.118 Ok Ok Ok Ok Ok Ok Ok Ok 0.306 Status Ok Mod Sub-Module Model
--- --------------------------- --------------- --------------- ------- ------1
Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 2 Policy Feature Card 2 WS-F6K-PFC2 2
Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 4 Distributed Forwarding Card WS-F6K-DFC
5 Distributed Forwarding Card WS-F6K-DFC 9 Distributed Forwarding Card
WS-F6K-DFC 11 Distributed Forwarding Card WS-F6K-DFC 12 Distributed Forwarding
Card WS-F6K-DFC 13 Distributed Forwarding Card WS-F6K-DFC Router# 3.3. 向冗余
Supervisor Engine 拷贝 IOS 文件如果二块 supervisor Engine 与第一块的 IOS 相同，就不需要做此步
使用以下命令将文件拷贝到冗余 supervisor engine 的 slot0: Router# copy
source_device:source_filename slaveslot0:target_filename 使用以下命令将文件拷贝到冗余
推荐阅读
- 交换机配置- 使用channel方式封装子接口
- 通过串口连接设置来管理交换机
- Cisco交换机配置注意事项
- 智能三层交换机的过滤策略综合说明
- 局域网交换机容易被忽视的五种功能
- 解决密码遗忘 交换机密码破解全攻略
- 学会配置交换机堆叠 步入新技术的顶峰
- 交换机防火墙配置管理下的注意事项
- 思科交换机设置技巧：MAC地址
- 如何配置三层交换机创建VLAN